GELE Surveying (Geomatics) — Spiral (Transition) CurvesCheat Sheet
Spiral (Transition) Curves cheat sheet — the reference card you wish you had on exam day. Condensed from the full study notes, this is the high-yield core of Spiral (Transition) Curves for GELE Surveying (Geomatics). Download, print, revise.
Exam context
The Geodetic Engineer Licensure Examination is conducted by Professional Regulation Commission (PRC) — Board of Geodetic Engineering and is scheduled for September 2026. The Surveying (Geomatics) subtest is marked as "Core" in the official pattern, and Spiral (Transition) Curves appears in position 6th of 9 in the GELE Surveying (Geomatics) review rotation. Passing mark: 70% weighted average, no sub-test below 50%. Recent GELE 2026 papers have drawn roughly a meaningful share of questions from this subject.
Spiral (Transition) Curves - Cheat Sheet
Last-minute reference for spiral curve formulas, superelevation mechanics, and board-exam shortcuts. Master the spiral angle, shift, throw, and speed–radius relationships in under 30 minutes.
Sections
Formulas
Formula
θₛ = Lₛ / (2R) [radians]
Meaning
θₛ = spiral angle (rad); Lₛ = spiral length (m); R = circular curve radius (m)
Watch Out
Answer is in RADIANS. Convert to degrees by multiplying by 180/π ≈ 57.3. Most board errors here.
When To Use
Always the first step — calculate spiral angle from spiral length and radius.
Formula
θₛ (deg) = (Lₛ × 90°) / (πR)
Meaning
Direct conversion to degrees without intermediate radian step.
Watch Out
The constant 90/π ≈ 28.65° per radian. Do NOT use 360 in place of 90.
When To Use
When the question directly asks for degrees or gives all data in metric.
Formula
θ(ℓ) = θₛ × (ℓ/Lₛ)²
Meaning
θ = deflection angle at distance ℓ from spiral start; ℓ = distance along spiral (m)
Watch Out
The angle varies with the SQUARE of relative distance. Many students forget the squared term.
When To Use
Find the angle at any intermediate point on the spiral—NOT linear, but squared.
Formula
Throw ≈ Lₛ² / (6R)
Meaning
Tangential offset at the end of the spiral (perpendicular distance from extended tangent to circle).
Watch Out
This is 4× the shift p. Do not confuse throw with shift—boards test both separately.
When To Use
Shift the circular curve outward; used in surveying and staking.
Formula
Shift p ≈ Lₛ² / (24R)
Meaning
Inward lateral shift of the circular arc center due to the spiral.
Watch Out
Shift = Throw / 4. If you calculate throw, divide by 4 for shift. Reciprocal error common.
When To Use
Calculate how much to move the circle inward from the original tangent alignment.
Common Values
Value
4° to 12°
Symbol
θₛ
Quantity
Spiral angle (typical highway)
Value
~20–40 m (depends on road class)
Symbol
Lₛ
Quantity
Spiral length per 10 mm superelevation runoff
Value
57.296°
Symbol
—
Quantity
Conversion: 1 radian
Section Title
Spiral Geometry & Angles
Important Facts
- Spiral curvature increases LINEARLY with distance from the start.
- The spiral angle θₛ is directly proportional to Lₛ and inversely proportional to R.
- Spiral length Lₛ is often set to develop superelevation over its extent.
- The deflection angle at distance ℓ depends on (ℓ/Lₛ)², NOT on ℓ alone.
- On a circular curve alone (no spiral), curvature is constant = 1/R.
- Spirals are also called easement curves or transition curves.
- A zero-length spiral is a discontinuity (abrupt tangent-to-circle jump).
Key Definitions
Term
Spiral Curve
Example
A 80 m spiral leading into a 300 m radius curve on a highway.
Definition
A transition curve in which curvature increases linearly with distance, easing a vehicle from a tangent (infinite radius) to a circular curve (finite radius R).
Term
Spiral Angle (θₛ)
Example
θₛ = 0.1333 rad = 7.64° for Lₛ = 80 m, R = 300 m.
Definition
The total angle (in radians or degrees) through which the spiral turns—the change in direction from tangent to the start of the circular curve.
Term
Throw
Example
Throw ≈ 1.07 m for Lₛ = 80 m, R = 300 m.
Definition
The perpendicular offset distance from the extended tangent line to the point where the spiral meets the circular curve.
Term
Shift (p)
Example
Shift p ≈ 0.267 m for the same spiral (one-quarter of the throw).
Definition
The lateral inward displacement of the circular arc's center relative to its original position on the tangent.
Term
Curvature (κ)
Example
At midpoint of spiral, κ = 1/(2R).
Definition
The reciprocal of radius, κ = 1/R. On a spiral, κ increases linearly with distance: κ = ℓ/(Lₛ × R).
Diagrams To Know
- Spiral entry: tangent → spiral → circular arc, showing decreasing radius.
- Spiral angle growth: graph of θ vs. ℓ/Lₛ (quadratic curve, not linear).
- Shift and throw geometry: tangent line, offset circle, and offset measurement.
- Curvature vs. distance: linear increase from 0 (on tangent) to 1/R (on circle).
Formulas
Formula
e + f = V² / (127 × R)
Meaning
e = superelevation rate (decimal, e.g., 0.06); f = side friction factor; V = design speed (km/h); R = curve radius (m)
Watch Out
The 127 constant ONLY works if V is in km/h and R is in meters. Always check units first. This is THE most-tested formula.
When To Use
Whenever you need the total centripetal demand (superelevation + friction) for a given speed and radius.
Formula
e = V² / (127 × R) − f
Meaning
Rearranged: superelevation rate = total demand minus available friction.
Watch Out
If e comes out negative, it means friction alone can provide the required centripetal force—no banking needed.
When To Use
Calculate the minimum superelevation needed when friction is known.
Formula
V_max = √[127 × R × (e + f)]
Meaning
Maximum safe speed given radius, superelevation, and friction.
Watch Out
Do NOT forget the square root. Solve for V by taking the square root of the product.
When To Use
Determine speed limit for a designed curve.
Formula
f = V² / (127 × R) − e
Meaning
Side friction factor demanded when superelevation is fixed.
Watch Out
If f > 0.20, the curve is unsafe at that speed—either reduce speed or add superelevation.
When To Use
Check if required friction exceeds safe limits (typically f ≤ 0.15–0.20).
Formula
Superelevation runoff rate = e / L_runoff
Meaning
e = superelevation rate; L_runoff = length over which e is applied (m).
Watch Out
Common runoff rates: 1 in 150 to 1 in 200 for highways. A rate of 1 in 200 means e = 1/200 per meter = 0.005 per meter.
When To Use
Design the approach taper—how quickly superelevation rises from 0 to maximum.
Common Values
Value
50–60 km/h
Symbol
V
Quantity
Typical design speed (urban collector)
Value
80–100 km/h
Symbol
V
Quantity
Typical design speed (provincial highway)
Value
0.08–0.10 (8–10%)
Symbol
e_max
Quantity
Maximum safe superelevation
Value
0.15–0.20
Symbol
f_max
Quantity
Maximum safe side friction
Value
1 in 150 to 1 in 200
Symbol
—
Quantity
Typical runoff rate
Section Title
Superelevation & Design Speed
Important Facts
- Superelevation + friction TOGETHER resist the centripetal force; neither alone is sufficient.
- The constant 127 = 9.81 × (3.6)²; it converts the physics formula to engineering units.
- Maximum safe superelevation on ordinary highways: e ≤ 0.08 (8%); on high-speed interstates: e ≤ 0.10.
- Maximum safe side friction: f ≤ 0.15–0.20 depending on pavement condition and tire grip.
- If design speed increases, either radius must increase or superelevation/friction must increase.
- Superelevation runoff is often tied to spiral length: superelevation develops over the spiral.
- The relationship e + f = V²/(127R) is non-linear: doubling speed requires quadrupling the lateral force demand.
Key Definitions
Term
Superelevation (e)
Example
e = 0.06 (6%) means the outer edge is 6 m higher per 100 m of width.
Definition
The inward banking (tilt) of a road surface, expressed as a decimal or percentage. Helps resist centrifugal force on curves.
Term
Side Friction Factor (f)
Example
f = 0.15 on a wet asphalt road; f ≈ 0.08 on wet concrete.
Definition
The ratio of available lateral friction to vehicle weight; depends on tire-pavement interaction. Typical range: 0.10–0.20.
Term
Design Speed (V)
Example
V = 80 km/h for a provincial highway.
Definition
The speed used to set curve radius, superelevation, and visibility—typically 85th percentile of free-flow traffic.
Term
Centripetal Demand
Example
At V = 80 km/h, R = 300 m, the demand is 0.168 (17% of weight).
Definition
The combined lateral force (as a ratio of weight) needed to keep a vehicle on a curved path: e + f.
Term
Runoff Length
Example
A runoff of 200 m to apply e = 0.06 gives a rate of 1 in 3333.
Definition
The distance over which superelevation transitions from normal crown to full banking (or vice versa).
Diagrams To Know
- Superelevation demand curve: V² vs. radius, showing how demand increases with speed.
- Cross-section of banked curve: angle of inclination, width, and height difference.
- Superelevation development: profile view showing transition from flat to full bank over runoff length.
- Side-friction limit boundary: regions of safe/unsafe combinations of e and V.
Reactions Or Equations
Note
Rearrangement of the fundamental superelevation formula. Useful for speed-radius design trade-offs.
Equation
V² = 127 × R × (e + f)
Conditions
V in km/h, R in m, e and f as decimals.
Note
9.81 m/s² is gravity; 3.6 converts m/s to km/h. The product gives the magic number 127.
Equation
127 = 9.81 × (3.6)² = 9.81 × 12.96
Conditions
Derivation of the units constant.
Formulas
Formula
Lₛ_min = 2 × R × θₛ (rearranged: Lₛ = 2Rθₛ)
Meaning
Minimum spiral length to achieve a target spiral angle θₛ (in radians).
Watch Out
If θₛ is in degrees, convert to radians FIRST by dividing by 57.3 (or multiplying by π/180).
When To Use
Ensure the spiral is long enough to develop curvature smoothly.
Formula
Lₛ = e × W / r_rate
Meaning
Lₛ = spiral length (m); e = superelevation (decimal); W = road width (m); r_rate = runoff rate (e.g., 1/200).
Watch Out
A runoff rate of 1 in 200 means r_rate = 1/200 = 0.005 per meter. Many students confuse the rate direction.
When To Use
Design spiral length to develop superelevation over a specified runoff rate.
Formula
Lₛ = (W × e) / (2.15 × V / 100)
Meaning
Alternative form relating spiral length to road width, superelevation, and vehicle speed for smooth steering transition.
Watch Out
This formula varies by jurisdiction. Always verify which standard applies (Philippine road code, AASHTO, etc.).
When To Use
Some design codes use this empirical relationship; check local standards (DPWH, NSCP).
Formula
Lₛ_superelevation = (e × W) / rate
Meaning
Spiral length to develop superelevation e over a road of width W with a given runoff rate.
Watch Out
Runoff rate is often given as '1 in X'—make sure to use the reciprocal (1/X).
When To Use
Most practical for Philippine highway design: set runoff rate (1/150–1/200) and solve for Lₛ.
Common Values
Value
2° to 3°
Symbol
θₛ_min
Quantity
Minimum spiral angle (design guideline)
Value
1 in 150 to 1 in 200
Symbol
—
Quantity
Preferred runoff rate (highways)
Value
80 m
Symbol
Lₛ
Quantity
Typical spiral length (80 km/h, 300 m curve)
Section Title
Spiral Length & Minimum Design
Important Facts
- Spiral length must satisfy TWO constraints: (1) minimum angle, (2) superelevation runoff rate.
- Use the LARGER of the two computed lengths to ensure both criteria are met.
- Runoff rates of 1 in 150–200 are standard for highways; 1 in 100 for urban streets.
- A too-short spiral causes abrupt centripetal acceleration and superelevation 'kink' (visible crown break).
- A too-long spiral wastes right-of-way but provides smoother transitions (more comfortable).
- Philippine DPWH standards typically require minimum spiral angles of 2°–3° on modern highways.
Key Definitions
Term
Minimum Spiral Length
Example
For θₛ = 3°, R = 500 m: Lₛ_min ≈ 52 m.
Definition
The shortest spiral required by design code to safely transition from tangent to circular curve without abrupt steering demand.
Term
Runoff Rate
Example
A rate of 1 in 200 over 100 m develops e = 100 × (1/200) = 0.50 (50%)—too steep; use longer Lₛ.
Definition
The slope of superelevation development, expressed as a ratio (e.g., 1 in 200 means e increases by 0.005 per meter of Lₛ).
Term
Spiral Ease
Example
Longer spirals (larger Lₛ) provide easier transitions for high-speed vehicles.
Definition
A measure of how smoothly the spiral transitions the driver's steering input; related to the rate of curvature change.
Diagrams To Know
- Spiral length vs. design speed: shows how faster roads need longer spirals.
- Runoff rate diagram: profile of superelevation development over Lₛ.
- Spiral envelope: plan view showing how the spiral 'wraps' from tangent into circle.
Section Title
Board Exam Problem Types & Solutions
Important Facts
- TYPE 1: Given Lₛ and R, find θₛ → Use θₛ = Lₛ/(2R) and convert if needed.
- TYPE 2: Given V, R, find e (with known f) → Use e = V²/(127R) − f.
- TYPE 3: Given e, runoff rate, find Lₛ → Use Lₛ = (e × W) / (runoff rate).
- TYPE 4: Given Lₛ, R, find angle at point ℓ → Use θ = [Lₛ/(2R)] × (ℓ/Lₛ)².
- TYPE 5: Given V, R, find max safe speed or check if speed is safe → Rearrange and solve.
- TYPE 6: Find spiral shift/throw → Use p ≈ Lₛ²/(24R) and throw ≈ Lₛ²/(6R).
- Always verify units: V in km/h, R in m, angles in rad (then convert to deg if needed).
- For runoff problems, runoff rate of '1 in 200' means multiply Lₛ by (1/200).
Diagrams To Know
- Step-by-step solution flowchart: identify known values → select formula → solve.
- Unit conversion checklist: km/h to m/s, degrees to radians, etc.
- Common answer-check methods: does the answer pass the 'reasonableness' test?
Must Remember
- 1. THE MAGIC 127: e + f = V²/(127R) only works if V is in km/h and R is in meters. Wrong units = wrong answer.
- 2. SPIRAL ANGLE: θₛ = Lₛ/(2R) gives radians. ALWAYS convert to degrees by multiplying by 57.3 (or 180/π). Board loves trapping this.
- 3. THE SQUARE RULE: Deflection angle at distance ℓ is θ = θₛ(ℓ/Lₛ)². NOT linear—the squared term is critical. Missed by 60% on board exams.
- 4. THROW vs. SHIFT: Throw ≈ Lₛ²/(6R); Shift p ≈ Lₛ²/(24R). Shift = Throw/4. Boards test both separately; confusing them loses 2 points.
- 5. SUPERELEVATION RANGE: Max e ≈ 0.06–0.08 (6–8%) on ordinary highways, 0.10 on high-speed interstates. If your answer exceeds this, flag it.
- 6. SIDE FRICTION LIMIT: Max f ≈ 0.15–0.20 depending on conditions. If required f exceeds 0.20, the curve is unsafe—speed must reduce or radius increase.
- 7. RUNOFF RATE TRAP: A rate of '1 in 200' means (1/200) = 0.005 per meter, NOT 200 m per unit e. Reciprocal error kills 30% of runoff problems.
- 8. TWO-CONSTRAINT RULE: Spiral length must satisfy BOTH minimum angle requirement AND superelevation runoff rate. Use the LARGER of the two Lₛ values.
- 9. QUADRATIC vs. LINEAR: Spiral curvature increases linearly with distance, but deflection angle increases with the SQUARE of relative distance. Mixing these up breaks geometry problems.
- 10. UNITS CHECKLIST: Before every calculation, verify: V in km/h? R in m? Angle in rad or deg? Runoff as decimal fraction? One unit error = full problem wrong.
Last Minute Tips
- FORMULA SELECTION TIP: If given Lₛ and R first, go straight for θₛ = Lₛ/(2R). If given V and R first, go for e + f = V²/(127R). The 'givens' hint which formula to deploy.
- REASONABLENESS CHECK: Spiral angles should be 2°–12° on most highways. Angles >15° or <1° are red flags. Superelevation should be 0.04–0.10. If your answer is outside these ranges, recheck the formula and units.
- EXAM RHYTHM: On a 3-hour PRC exam, spiral problems typically appear in 2–3 questions. Budget 10 minutes per problem: 2 min read, 5 min setup+formula, 2 min solve, 1 min check. Don't linger on units—verify once at the start.
- COMMON BOARD TRAP: Exams often mix spirals and circular curves in one problem. Make sure you identify which formula applies to which segment. Spiral angle θₛ ≠ arc angle of the main curve.
- LAST-MINUTE MEMORY AID: 'TST' = 'Throw, Shift, Two-fourths.' Throw is Lₛ²/(6R); Shift is one-quarter: Lₛ²/(24R). The numerator is Lₛ²; denominators are 6 and 24. Works every time.
Comparison Tables
Rows
Values
- Perpendicular offset from tangent to spiral end
- Inward lateral displacement of circle center
Property
Definition
Values
- ≈ Lₛ² / (6R)
- ≈ Lₛ² / (24R)
Property
Formula
Values
- Throw = 4 × Shift
- Shift = Throw / 4
Property
Relationship
Values
- Adjust horizontal tangent offset in survey
- Shift circular arc inward on plan
Property
Used for
Values
- ≈ 1.07 m
- ≈ 0.27 m
Property
Example (Lₛ=80m, R=300m)
Columns
- Property
- Throw
- Shift (p)
Table Title
Throw vs. Shift: Common Confusion
Rows
Values
- Road banking (outward tilt)
- Tire-pavement grip
Property
What is it?
Values
- Permanent feature of the road geometry
- Depends on tire condition, pavement, weather
Property
How is it applied?
Values
- No (but can be near 0)
- No (always resisting motion)
Property
Can be negative?
Values
- 0.04–0.08 (4–8%) max
- 0.10–0.20 (10–20%) available
Property
Typical magnitude
Values
- No (fixed by design)
- Partially (by braking/cornering control)
Property
Controllable by driver?
Values
- Designed-in component
- Backup if e is insufficient
Property
In formula e + f = V²/(127R)
Columns
- Feature
- Superelevation (e)
- Side Friction (f)
Table Title
Superelevation vs. Friction: Roles in Centripetal Force
Rows
Values
- θₛ = Lₛ / (2R)
- radians
- Forgetting to convert to degrees
Property
Lₛ (m), R (m) → rad
Values
- θₛ = (Lₛ × 90) / (πR)
- degrees
- Using 360 instead of 90 in numerator
Property
Lₛ (m), R (m) → deg
Values
- θₛ (deg) = θₛ (rad) × 57.3
- degrees
- Using 180/π ≈ 57.3 incorrectly
Property
θₛ (rad) → deg
Values
- θₛ (rad) = θₛ (deg) / 57.3
- radians
- Multiplying instead of dividing
Property
θₛ (deg) → rad
Columns
- Input Units
- Formula
- Output
- Common Error
Table Title
Spiral Angle Calculation: Units Trap
Previous chapter
Horizontal Curves (Simple, Compound, Reverse)
Next chapter
Vertical (Parabolic) Curves
Ready to practise for the GELE 2026?
Super Tutor's AI review plan adapts to your weak areas and builds a weekly practice schedule around your target GELE exam date.